At a glance
- EN 1467:2022 defines gross size (smallest circumscribed cuboid) and net size (greatest inscribed cuboid). Commercial size refers to gross or net size, excludes recognised defects and may allow a reduction, "usually net size dimensions minus 0,05 m"1.
- Dimensions are reported in metres to two decimals, volume in cubic metres and mass in tonnes to three decimals. Shapeless blocks are measured commercially only by mass1.
- A 2018 Ukrainian study of granite blocks lists five sources of tape-measurement error and reports that the error in commercial volume rises with block volume3.
- In the sources we reviewed, we found no study comparing tape-measured and scan-measured commercial volume on real traded blocks.
Three boxes around one stone
A rough block may have uneven faces, chipped edges or a sloping corner. For a block sold by volume, buyer and seller need to agree how the block is measured: which dimensions determine the invoice. The European standard for rough blocks, EN 1467:2022, gives three sizes and leaves the parties to say which one they mean1.
- Gross size: "size defined by the lengths of the edges of the smallest cuboid circumscribed to a rough block" (clause 3.2)1. In plain words, the box the whole stone fits in.
- Net size: "size which is determined by establishing the greatest inscribed cuboid block" (3.3). Its note adds that the inscribed cuboid "shall not contain any sides without right angles nor contain drill holes and other holes"1.
- Commercial size: the definition (3.4) reads "size obtained by reducing each net size dimension"1. The measurement clause (4.1.1) adds that commercial size "refers either to gross or net size and excluding recognized defects and it may allow for a general reduction for commercial purpose only, usually net size dimensions minus 0,05 m"1. The 0.05 m is the usual figure, not a fixed rule, and the base can be gross or net, so a contract has to state both.
Gross and net sizes bracket the stone's geometry; commercial size is a pricing quantity. A trade reduction is stone the buyer does not pay for, not stone that is missing, so a mass estimate needs a physical volume and the measured apparent density.
The standard also fixes the order of the dimensions: length l ("greater side in a natural layer where appropriate"), width b and height h ("side at right angles to the natural layer or to the plane containing length l and width b"), given in that sequence (3.1)1.
- Gross: 3.20 × 2.05 × 1.75 m. The smallest box that encloses the block, touching its outermost points.
- Net: 2.90 × 1.85 × 1.55 m. The largest box inside the block, clear of the sloping corner and the drill-hole trace.
- Commercial: 2.85 × 1.80 × 1.50 m. Example: net minus 0.05 m per dimension, a trade allowance (0.025 m in from each opposite face).
- The natural layer. Height h is measured at right angles to it; l and b lie along it.
What EN 1467:2022 asks for
- Method and reporting resolution. All measurements are carried out in accordance with EN 13373 and "indicated in metres to two decimals places"1. That is how the figure is written down, not a statement of how accurate the instrument is.
- Volume. Stated "in cubic metres to three decimals places"; it "may be calculated by dividing the mass of the block by the apparent density"1.
- Mass. "Stated in tonnes with three decimals"1.
- Squared or shapeless. A squared block is one "which corresponds approximately to a regular cuboid" (3.8); its six sides "shall be approximately flat, right-angled and parallel", and "deviations from the cuboid shape are permitted" (4.1.2)1. A note to 3.8 adds a numerical guide: "Normally" the block's mass divided by its apparent density "should be bigger than 80 % of the gross size"; at 80% or less, "the block is considered a shapeless rough block"1. Mass ÷ density is a volume, so the comparison is with the volume of the gross cuboid.
- Shapeless blocks are measured by mass. "For commercial purposes, shapeless rough blocks shall be measured only by mass, gross size shall be provided upon request" (4.1.4)1.
- Blocks of specific size must have dimensions between the minimum and maximum "agreed between the purchaser and supplier" (4.1.2)1.
EN 1467:2022 replaced the 2012 edition. Its foreword lists the main technical changes: a "new definition of the commercial size of a rough block in 3.4", "measurement criteria for the commercial size changed", and more detail on factory production control1. Parties working from different editions or local habit can reach different commercial volumes for the same stone. We read the preview pages only; the full standard is sold by national standards bodies.
EN 13373, the test-method standard that EN 1467 points to, covers the geometric characteristics of natural stone products, including rough blocks2. Its scope says its methods "can be applied in the case of a dispute between two parties" but are "not compulsory for production control", and that "other measuring equipment can be used as long as their precision can be demonstrated to be equal or better"2. A scanner is therefore not excluded, but whoever uses it has to show its precision.
How blocks are measured in practice
Tape measurement is the method examined in a 2018 Ukrainian study of granite blocks; a separate 2020 study of a Portuguese limestone quarry describes blocks "inspected for flaws, visually by a worker"3,7. The Ukrainian group lists five factors that degrade a tape measurement and the volume calculated from it3:
- The shape and size of the natural blocks the deposit produces3.
- The volume of the block: the authors report "a directly proportional relationship" between a block's volume and the error in its commercial volume3.
- Uneven faces and chipped edges, which differ between split and sawn blocks3.
- The human factor: use of the tool and the choice of the two points between which a net dimension is taken3.
- Temperature, which stretches or shrinks the tool3.
The authors argue that calculating useful volume from net dimensions leads to an overestimation of block prices3. They propose a "block passport" with a 3D model of the block, its gross, net and commercial volumes, and the accuracy of its commercial volume3. They also propose quality classes based on the difference between gross and commercial volume (A up to 15%, B up to 30%, C up to 50%, D more than 50%), but the paper does not say whether the percentage is taken of gross or of commercial volume3. These classes are a research proposal, not a trade rule.
Deductions for defects are not spelled out. Clause 4.1.1 has commercial size "excluding recognized defects"1; the preview pages we read do not say how a defect is recognised or how much is taken off for it. We looked for documented national customs and found only sellers' web pages, not studies or trade-body rules.
Worked examples: how far apart the three volumes are
Example A. Assumptions: an irregular marble block whose smallest enclosing box measures 3.20 × 2.05 × 1.75 m and whose largest inscribed box measures 2.90 × 1.85 × 1.55 m; the parties have agreed commercial size as net minus 0.05 m on each dimension, the usual reduction named in EN 14671. The dimensions are illustrative.
- Gross volume: 3.20 × 2.05 × 1.75 = 11.480 m³.
- Net volume: 2.90 × 1.85 × 1.55 = 8.316 m³, which is 27.6% less than gross.
- Commercial volume: 2.85 × 1.80 × 1.50 = 7.695 m³, which is 7.5% less than net and 33.0% less than gross.
At the same price per cubic metre, an invoice on gross volume would be 49.2% higher than one on commercial volume for this block.
Example B. Assumptions: a smaller block, gross 2.15 × 1.40 × 1.20 m, net 1.95 × 1.25 × 1.05 m, same agreed 0.05 m reduction. Illustrative dimensions.
- Gross volume: 3.612 m³.
- Net volume: 2.559 m³, 29.1% less than gross.
- Commercial volume: 1.90 × 1.20 × 1.00 = 2.280 m³, 10.9% less than net and 36.9% less than gross.
The same 0.05 m takes a larger share from the smaller block (10.9% against 7.5%).
| Block | Gross (m³) | Net (m³) | Commercial (m³) | Commercial vs net | Commercial vs gross |
|---|---|---|---|---|---|
| A: gross 3.20 × 2.05 × 1.75 m | 11.480 | 8.316 | 7.695 | −7.5% | −33.0% |
| B: gross 2.15 × 1.40 × 1.20 m | 3.612 | 2.559 | 2.280 | −10.9% | −36.9% |
The 80% note. Suppose block A weighs 26.1 t on the weighbridge and its measured apparent density is 2.70 t/m³ (assumed values). Its physical volume is then 26.1 ÷ 2.70 = 9.667 m³, or 84.2% of its gross volume. It clears the note's normal 80% threshold; whether it is a squared block also depends on its geometry, which must approximate a cuboid1. If it weighed 24.0 t, the figure would be 8.889 m³, or 77.4% of gross volume, and under the note the block would be considered shapeless, to be measured commercially by mass1. The density used should be the measured apparent density of that material (test method: EN 19368), not a generic value.
Rounding. Example: if otherwise exact dimensions are rounded to the nearest 0.01 m, each rounding error is at most 0.005 m. If all three net dimensions of block A were rounded up by the full 0.005 m, its net volume would rise by 0.77%; for block B by 1.14%. This is the effect of writing figures to two decimals1, separate from any measuring error.
What scanning measures, and what the tests show
Photogrammetry builds a 3D model from overlapping photographs; LiDAR and laser scanners measure distance with light. A surface model can in principle be used to fit the boxes and compute volume, as the Ukrainian study proposes for its block passport3.
What the published tests show:
- Close-range photogrammetry, one small object. In a 2008 test, the photogrammetric volume of a plaster cone of about 364 ml came to 98.72% of its volume measured by water displacement; the authors write that it "can be as precise as 98,72 %"4. One laboratory object, not a block.
- Phone LiDAR, small objects and a cliff. The iPhone 12 Pro sensor produced models of "small objects with a side length > 10 cm with an absolute accuracy of ± 1 cm", and models of a coastal cliff up to 130 × 15 × 10 m with an absolute accuracy of ±10 cm5. These are linear accuracies of the model, not volume accuracies, and neither object was a stone block.
- Survey instruments on blocks. The Ukrainian study surveyed blocks from base points, with a laser rangefinder described as having "an error of 2 mm", and found surveying from four base points the most accurate of its schemes3.
- Marble is a difficult surface for lasers. Tests on marble samples found that marble's "translucency and heterogeneous structure produce significant bias and increased noise" in laser range measurements6. The study concerns precision scanning of marble surfaces; its abstract does not quantify the effect on block-volume measurement.
What has not been studied
In the sources we reviewed, we found no study that measures a set of real traded blocks both by tape and by scan and compares the commercial volumes. The test figures above come from a small plaster object, small objects and a cliff, not from blocks in a dusty yard with wet faces and chipped edges. Nor did we find a paper on how often buyers and sellers disagree on block volume. A retained surface model can make the measured geometry inspectable by both sides. Coverage, reconstruction, box fitting and defect deductions must still be specified, and commercial-volume accuracy on traded blocks was not established in the studies we found.
What a sales contract should state
This is good practice, not a legal duty. A block sale is clearer when the contract or block list states:
- Which size the price applies to: gross, net or commercial, by name1.
- For commercial size, the base and the reduction: gross or net size, and whether the usual 0.05 m reduction of net dimensions or another figure applies1.
- How defects are handled: which defects are excluded and how, since the preview clauses we read do not define "recognized defects"1.
- The measuring method: EN 13373, tape or scan, who measures, where and when2.
- Reporting: metres to two decimals, cubic metres and tonnes to three1.
- The density used for weight, with its source, ideally the measured apparent density of the material8.
- The rule for shapeless blocks: measured by mass in tonnes, with gross size on request1.
- What happens in a dispute: a re-measurement by an agreed method; EN 13373 says its methods can be applied in a dispute2.
For what measurement differences can cost a seller, see where quarries lose money on block inventory; for how much extracted rock becomes block, see block recovery in dimension stone quarries.
Frequently Asked Questions
What is the difference between gross, net and commercial size of a block?
Under EN 1467:2022, gross size comes from the smallest cuboid circumscribed to the block and net size from the greatest inscribed cuboid without non-right-angled sides or holes1. Commercial size refers to gross or net size, excludes recognised defects and may allow a reduction, usually net dimensions minus 0.05 m1. In our Example A, the three volumes are 11.480, 8.316 and 7.695 m³.
How precisely must a stone block be measured?
EN 1467:2022 asks for dimensions in metres to two decimal places, measured in accordance with EN 13373, with volume in cubic metres and mass in tonnes, each to three decimals1. These are reporting rules, not instrument tolerances. EN 13373 allows other measuring equipment if its precision is shown to be equal or better than the methods it describes2.
When is a block sold by weight instead of volume?
When it is shapeless. A note in EN 1467:2022 says that normally a squared block's mass divided by its apparent density should exceed 80% of the volume of its gross size, and that at 80% or less the block is considered shapeless1. Shapeless blocks are measured commercially only by mass, in tonnes, with gross size provided on request1.
Is 3D scanning more accurate than a tape for blocks?
The evidence we found does not answer this. A phone LiDAR gave about ±1 cm linear accuracy on small objects over 10 cm5, photogrammetry gave 98.72% of a small plaster object's displaced volume4, and marble's translucency adds bias to laser readings6. We found no study comparing tape and scan volumes on real traded blocks.
How Noria Strata handles this
In Noria Strata each block has one card with its sizes, volume and weight, a 3D model from a LiDAR scan with the phone, and photographs of all six sides taken with a capture guide so none is missed. The card stays with the block from the quarry face to the buyer, and a buyer can be sent a link to turn the block in 3D and see the same sizes. See blocks for how the card works, or try the block weight calculator to see how volume and density set a block's weight.
Sources
- CEN (2022). EN 1467:2022 Natural stone – Rough blocks – Requirements. Preview pages of SIST EN 1467:2022 (foreword; clauses 1, 3.1–3.8, 4.1.1–4.1.4) cdn.standards.iteh.ai/samples/72591/b25b7404e3cb4139b24cb91ca3cfd48c/SIST-EN-1467-2022.pdf
- CEN (2020). EN 13373:2020 Natural stone test methods – Determination of geometric characteristics on units. Catalogue page of the Serbian adoption SRPS EN 13373:2020, Institute for Standardization of Serbia iss.rs/en/project/show/iss:proj:64181
- Levytskyi, V., Makhno, A., Panasiuk, A. & Mamrai, V. (2018). Dimension stone blocks modelling based on digital surface model methods. Visnyk ZhDTU / Technical Engineering 2(82): 259–267. DOI 10.26642/tn-2018-2(82)-259-267 vtn.ztu.edu.ua/article/view/148590/148012
- Yakar, M. & Yilmaz, H. M. (2008). Using in volume computing of digital close range photogrammetry. International Archives of the Photogrammetry, Remote Sensing and Spatial Information Sciences XXXVII-B3b: 119–124 isprs.org/proceedings/XXXVII/congress/3b_pdf/22.pdf
- Luetzenburg, G., Kroon, A. & Bjørk, A. A. (2021). Evaluation of the Apple iPhone 12 Pro LiDAR for an Application in Geosciences. Scientific Reports 11: 22221. DOI 10.1038/s41598-021-01763-9 doi.org/10.1038/s41598-021-01763-9
- Godin, G., Beraldin, J.-A., Rioux, M., Levoy, M., Cournoyer, L. & Blais, F. (2001). An Assessment of Laser Range Measurement of Marble Surfaces. Proc. Fifth Conference on Optical 3-D Measurement Techniques, Vienna University of Technology graphics.stanford.edu/papers/marble-assessment
- Monteiro, F. F. (2020). Integration of an optical system for 3D reconstruction. MSc extended abstract, Instituto Superior Técnico, Lisbon (thesis) fenix.tecnico.ulisboa.pt/downloadFile/1689244997262219/Resumo%20Alargado%20-%20Filipe%20Monteiro%2085082.pdf
- CEN (2006). EN 1936:2006 Natural stone test methods – Determination of real density and apparent density, and of total and open porosity. BSI catalogue page for BS EN 1936:2006 knowledge.bsigroup.com/products/natural-stone-test-methods-determination-of-real-density-and-apparent-density-and-of-total-and-open-porosity
How to cite this article
Konstantinou, M. (2026). How a quarry block is measured: gross, net and commercial size. Noria Strata. https://www.noriastrata.com/en/blog/how-a-stone-block-is-measured
The author
Maria KonstantinouCTO, Noria Strata
